US $35.00
| Condition | Used
:
An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
|
| Seller Notes | “Good usable condition and a few have a little surface rust but nothing to hurt the use of them. Check pictures and ask questions before bidding if not sure.” |
Directions
Similar products from Pats & Dies Sets
Vintage Rimac Rinck McILWAINE Hexset Taps and Dies
Hanson 26317 41-Piece Metric Tap & Die Set - 3mm-12mm
Quality TRW 3/4-14 NPT 5 FLUTE THREADING TAP USA used
New Vintage Craftsman Tap & Die Set - 5499
TEKTON 7559 Tap and Die Set, Metric, 39-Piece, 39 Metric
New York 7/8" 9-pitch tap set (3 taps, taper, plug and bottom) Made in USA
never used Irwin 76 pc. super tap and diet set in case
IRWIN HANSON 76 PIECE TAP & DIE SUPER SET 26376 MACHINE SCREW FRACTIONAL METRIC
Vintage Vermont Tap & Die Set 25 Pc.
LOT of 31 vintage HAND TAPS ~ MORSE GREENFIELD CARD LUCKY ST Co. NPT ~
Sossner 17115 5-40 M-Boss (Coform) GH5 Bottoming Tap, Forming Tap
OSG 1400157100 10-24 Forming (Coform) H6 Bottoming Tap, Forming Tap
General Tire Plain Type T-Handle Tap Wrench Set 0~1/4" & 1/4" ~1/2"
TAP HANDLE FROM TAP AND DIE SET
Hanson 25712 set 1/4-1/2 in HRT die set
Craftsman 75 piece Tap & Die Carbon Steel Set Combo Case SAE and Metric New NIB
VERMONT AMERICAN 21749 Tap and Die Set, 40 pc, Carbon Steel
People who viewed this item also vieved
1 pc Nachi 64311 HSS Hand Tap, 1-8NC T H4, New
1 pc Nachi 64313 HSS Hand Tap, 1"-8NC B GH4, New
3/8 X 16 NC HSG H3 4 FLUTE PLUG TAP 5-1/2 INCH OVERALL (C-5-2-2-8)
1 pc Nachi 64312 HSS Hand Tap, 1-8NC P H4, New
1 pc Nachi 64293 HSS Hand Tap, 7/8-9NC T H4, New
Acme CUTTING TOOLS TAP 7/8 US STD 10
WIDELL 6801, PIPE TAP, 3" - 6, LH, HSS, H-8, 9 7/8" LENGTH, 8 FLUTE, NNB
HANSON WHITNEY 41018, PIPE TAP, 1 1/2-6 NC, HS, GH-4, 4 FLUTE, 6 3/8" LENGTH
GREEN 1 3/8-12, PIPE TAP, NF, G, H-4, K6 HS, 6 FLUTE, 6" LENGTH
HANSON WHITNEY 9396, TAPS, HS, 5 FLUTE, 3 3/4" LENGTH, NIB
TFI 1 5/8-6, TAP PIPE, HS, H7, LH, 6 FLUTE, 6 5/8" LENGTH, 3 1/4" THREAD LENGTH
OSG 7/16-14 Tap, Spiral Point Bottom GH3, Bright Finish, 1232100
OSG, 7/16-14 Tap Spiral Point Plug GH3, Bright Finish, 1232000
FMT STANDARD HSS SPIRAL POINT TAP SIZE: NO. 8 THREAD: 32
FMT STANDARD HSS SPIRAL POINT TAP SIZE: NO. 10 THREAD: 24
FMT STANDARD HSS SPIRAL POINT TAP 3/8" SIZE 16 THREAD
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies
