Roemheld 1940 700 Threaded Body Push /pull-double-acting Hydraulic Work Support

US $118.00

  • Boiling Springs, South Carolina, United States
  • Jan 30th
Double-Acting push/pull hydraulic Threaded-Body Cylinder with plunger head Bolt  Hydraulic work supports are used to provide a self-adjusting  rest for the workpiece during the machining operations.  They compensate the work piece surface irregularities, also deflection and vibration under machining loads.  Two sizes are available. The threaded-body design  of the elements allows direct installation in clamping fixtures, in horizontal or vertical mounting position, and thereby a  space-saving arrangement. Hydraulic oil is fed through  drilled channels in the fixture body. Hydraulic locking is  made together with hydraulic clamping of the workpiece, or independently. Technical characteristics Functioning: s.a. with spring return Max. support force: [kN] 7 Plunger-?: [mm] 16 Plung. stroke: [mm] 8 Contact plunger: Spring force Off-position: Extended - spring force Position monitoring: without metallic wiper edge without self-locking no Shape of housing: Mounting body Variant of connection: Threaded-body type Piston rod end: Int.thread w.dome-head cont.bolt B1.940 Threaded-body work supports single acting max. operating pressure 500 bar For direct screwing-in for mean support forces in three versions: 1. off-position extended, contact and return by spring force 2. off-position retracted, extending hydraulically, contact and return by spring force 3. off-position retracted, extending and contact with air pressure, with spring return connection through drilled channels Perbunan seals plunger diameter 16 mm 2 sizes with max. support forces of 6.5 or 9.5 kN plunger strokes 8 and 15 mm New B1.943 Threaded-Body Work Support 4 sizes 3 types of function with venting of the spring area single acting max. operating pressure 500 bar B1.9470 Threaded-Body Work Supports with metallic wiper edge, single acting, max. operating pressure 70 bar For direct screwing-in for medium load forces at low operating pressure with metallic wiper edge and FKM wiper Hydraulic work supports are used to provide a self-adjusting rest for the workpiece during the  machining operations. They compensate the workpiece surface irregularities, also deflection and vibration under machining loads. Two sizes are available. The threaded-body design of the elements allows direct installation in clamping fixtures, in horizontal or vertical mounting position,  and thereby a space-saving arrangement. Hydraulic oil is fed through drilled channels in the fixture body. Hydraulic locking is made together with hydraulic clamping of the workpiece, or independently. There are three variations of plunger actuation:  1. Spring advanced; the plunger is extended in off-position. 2. Air pressure advanced; the plunger is retracted in off-position.  The pneumatically-actuated plunger allows precise setting of the plunger contact force  by means of a pressure reducing valve. 3. Hydraulic pressure and spring advanced; the plunger is retracted in off-position It moves forward with a light spring force against the workpiece, when hydraulic pressure is applied. Combination possibilities The work supports 194X-01X can be combined with the swing clamps as per data sheet B 1.891. (Example see reverse page) Operating conditions tolerances and other data see general characteristics A0.100. Work supports are not suitable to compensate side loads. General technical characteristics Support plunger-? [mm] 16 Stroke [mm] 8 Adm. support force at 500 bar 194X-00X [kN] 6,5 194X-01X [kN] 9,5 Recommended minimum pressure [bar] 100 b1940_Anzugsdrehmoment [Nm] 60 Weight [kg] ca. 0,25 Mounting dimensions, accessories and application examples see reverse page Load F [kN]   Operating pressure p [bar] Cylinders must be backed up for operating pressures exceeding 160 bar. Contact by spring force a [mm] 80,5 b [mm] 79 c [mm] 54 Spring force min./max. [N] 8/13 Seal 3000-842 is included in the delivery Dimensions Combination possibility Threaded-body work support with threaded-body swing clamps as per data sheet B 1.891 Support and clamping forces have to be adapted to each other, so that there will be sufficient force reserve available  for the threaded-body work support to absorb the machining forces. Thumb rule: Support force = 2 x clamping force The required minimum pressure is 200 bar. The diagram below shows the graphs of the clamping and support forces for the 2 possible combinations. Clamping force / support force F [kN]   Operating pressure Example Swing clamp 1891-XX1 clamps against threaded-body work support 194X-010. Operating pressure 200 bar. Support force 3.0 kN - Clamping force 1.5 kN = possible machining force 1.5 kN Accessories Mounting body part-no. 3467-086  as per data sheet B 1.460 or  body with pneumatic connection Part-no. 3467-112 Examples                                                 Payment from PayPal with confirmed address only. Items Will be Shipped by USPS Ground on the Same  or Next Business day of receiving full payment USPS Tracking Number will be provided with confirmation and for higher priced items insurance will be provided
Condition New other (see details) :
A new, unused item with absolutely no signs of wear. The item may be missing the original packaging, or in the original packaging but not sealed. The item may be a factory second or a new, unused item with defects. See the seller’s listing for full details and description of any imperfections.
Seller Notes work holding -Double-Acting push/pull hydraulic Threaded-Body plunger CylinderNew with no original box or instructions

Directions

Similar products from Clips & Jaws

People who viewed this item also vieved

By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.

Accept All Cookies