New-version-m328-version-of-inductor-capacitor-esr-meter-multi-function-tester

US $450

  • ???, ???, China
  • Jun 9th
Newest  version of the M328 version of inductor-capacitor ESR meter multi-function tester       1. Using 2014 V1.10 latest version of the software, use M328 chip functions more than the M8 version.   2. microcontrollers 8MHz external crystal, the measurement accuracy is better.   3. Accuracy of adoption-related resistance thousandth metal film resistors, and the remaining one percent also used metal film resistors.   4.LCD backlit LCD screen with low power consumption, compared with the overall power consumption is almost negligible, so the presence of the backlight time, easy reading in the dark.   5. Main chip and with a dual inline socket, ideal for electronics enthusiasts upgrade or replace the chip.   6. Using 9V laminated battery.   7. All components are made of high quality genuine. LCD screen for low-power-backlit screen, the backlight current of about 2mA, so after boot time has a backlight for easy use in the dark.     The main parameters and use:   1 using ATmega328 microcontroller.   212 864 graphic LCD display shows the results.   3 one-button operation, automatic power off.   4 shutdown current of only 20nA, support for battery operation.   5 supports automatic power off. ATmega328 when no measurement to reduce power consumption in sleep mode.   6 Automatic detection PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET, diodes, dual diode, thyristor SCR.   7 automatically detects the pin layout.   8 the threshold voltage and current amplification factor of the emitter junction of the bipolar transistor measurements.   9 Darlington transistor through a high threshold voltage and high-current amplification factor identified.   10 pairs of bipolar transistors, MOSFET protection diode testing.   The threshold voltage value 11 and the gate capacitance of a MOSFET is measured.   12 supports two resistance measurements and symbols show the highest four numbers and units. Both ends of the resistor symbol is shown connected to the tester probes number (1-3). Therefore, the potential can also be measured. If the potentiometer is adjusted to its end, the tester can not distinguish between the middle and the ends of the pin.   13 resistance measurement resolution is 0.1 ohms, the highest measured value 50M ohms.   14 can be detected and measured a capacitor. Maximum four numbers and units. Values can be from 25pf (8MHz clock, 50pF @ 1MHz clock) to 100mF. Resolution up to 1 pF (@ 8MHz clock).   15 may be larger than the value for 2UF capacitor equivalent series resistance (ESR) measured capacitance value. Resolution of 0.01 ohms and a two-digit numeric display. This feature requires at least 16K Flash ATMEGA (ATmega168 or ATmega328).   16 can display symbols of the two diodes in the right direction. In addition, the forward voltage drop displayed.   17 LED detection for diode forward voltage drop is much higher than normal. Dual LEDs detected as double diode.   Zener diode 18 can be detected, if the reverse breakdown voltage is less than 4.5V. This will appear as two diodes, can only be determined by the voltage. Probe around the diode symbol is the same, in which case, you can 700mV threshold voltage close to the true recognition diode anode!   19 If more than three diode type parts inspection, failure to establish the number of diodes another message. This will only happen if the diode is connected to all three probes and at least one diode. In this case, you should only connect the two probes and start measuring again, one by one.   20 measures a single diode reverse capacitance values. Bipolar transistors also can measure, if you connect the base and collector or emitter.   21 need to find a measurement of the full-bridge connection.   25pf capacitor values lower than 22 are usually undetectable, but with a diode in parallel or at least 25pf capacitor in parallel. In this case, you have to subtract part shunt capacitance values.   23 ohm resistor will measure inductance of less than 2100, if you have at least 16K ATMEGA flash. Range from 0: 01mH than 20H, but the accuracy is not good. Measurement results show only a single connection element.   24 test time is about two seconds, only the capacitance and inductance measurements will take longer.   25 software can be set to automatically turn off the power to measure the number of times before.   26 built-in self-test function with selectable clock frequency of 50Hz signal check the accuracy and wait for the call (ATmega328).      Note: Before measuring capacitance of the capacitor must be discharged, otherwise very likely damage the instrument     Package including   1x M328 ESR meter (battery not included)             Payment We accept the payment via PayPal only. Payment is expected within 5 days of the auction's end. Availability of the item can not be guaranteed if no payment received in 3 days. Please don't purchase if you are not intend to pay. Unpaid item will report to eBay and get the warning. .   Shipping & Handling   1.Items are shipped from china.we will send out within 2 working days after receive the money.   2.We usually send the parcel by Singapore Post Air Mail or HongKong Post Air Mail. After send out,most country will arrived the parcel in 12-25 business days. We also can provide Express,such as Fedex,DHL,EMS,usually 3-7days to most country.If you need Expedited shipping,contact us. The global shipping is difficult to control sometimes,if you havent receive after 25days,contact us,we will check for you. 3.We send to the address of ebay add info,please check your add info of ebay is correct.   4.Some conutries,such as Italy,Brazil,we can ship to,but it usually needs more than 30days to arrive,if you dont care the long time of shipping,contact us.   Warranty and Return  1.If you are not satisfied when you receive your item, please return it within 14 days for a replacement or money back. Please contact us before you return it.   2.If item is defective in 14 days, We will send you a replacement without extra charger, or offer refund after we receive the defective item.   3.If item is defective after 14 days, you can still send it back to us. We will send you a new one after receiving the defective item. But you have to pay the extra shipping free.                                                           Feedback please leave behind your positive feedback for us after you receive the item, no matter whether you are satisfactory with my item, we will leave behind the same to you. If you want to leave a negative feedback,please contact me at first, we trust that everything could be issued before you leave it. Contact us We work 6 days except Sunday and public holidays. Please feel free to contact us anytime if you have any questions , We will try our best to help you.
Condition:
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...
Brand Does Not Apply
MPN Does Not Apply

Directions

Similar products from Capacitance Testers & Meters

People who viewed this item also vieved

By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.

Accept All Cookies