MMA7361-Triple Axis Accelerometer Breakout for Arduino to Good Use, US $4.24 – Picture 0

MMA7361-Triple Axis Accelerometer Breakout for Arduino to Good Use, US $4.24 – Picture 1

MMA7361-Triple Axis Accelerometer Breakout for Arduino to Good Use, US $4.24 – Picture 2

Mma7361-triple Axis Accelerometer Breakout For Arduino To Good Use

US $4.24

???, ???, China
Jan 29th

Open on mobile:
QR code

MMA7361-Triple Axis Accelerometer Breakout for Arduino to Good Use Welcome Welcome to use “PIR Motion sensor Module” module. The modular is produced by ICStation in 2014. Product Features ICSG010A is the automatic control module based on infrared technology. D203S probe design, high sensitivity, strong reliability, ultra low voltage mode, widely used in all kinds of automatic induction electrical equipment, especially automatic control product dry batteries. Physical Picture Electrical Parameters Product Model ICSG010A Voltage Range 4.5-20DV Static Current <50uA Output Level High 3.3 V /Low 0V Trigger Mode L No Repeated trigger /H Repeated trigger Delay Time 0.5-200S(adjustable) can be produced range 0.1 seconds - a few minutes Blocking Time 2.5S(Default) can be produced range 0.1 seconds, tens of seconds Circuit Board Size 32mm*24mm Induction Angle <100 deg Working Temperature -15-+70 deg Induction Lens Size Diameter:23mm(Default) Function Features 1. Automatic induction: people into its sensing range outputs high level, people leave the sensing range automatic time delay closing high, a low output level. 2. Photosensitive control (can choose, the factory did not set) can be set to a photosensitive control, day or when light is strong not induction. 3. Temperature compensation (optional, the factory did not set): when the environment temperature is increased to 30 to 32 DEG C in the summer, the detection distances lightly shorter, temperature compensation for compensating the performance of certain. 4. Two kinds of triggers: (select jumper) 4.1. Unrepeatable trigger mode: induction output high level, delay time is over, the output will be automatically from high level to low level. 4.2. Repeated trigger mode: induction output high level, in the delay period, if the body is in its sensing range of activities, its output will maintain a high level, until the people left after the delay of the high level to low level (induction module detected each time the activities of the human body will automatically be extended a delay time, delay time and as a starting point to the last active time). 5. With the induction time blocked (default: 2.5S blocking time): induction module in every induction output (high level into low level), can be followed by setting up a blocked period, sensors in the time period does not accept any induction signal. This function can realize the "two induction output time" and "blockade" interval work, can be applied to the gap detection products; at the same time, this function can effectively suppress the interference generated in the process of the load switch. (this time can be set in a few tenths to tens of seconds). 6. Wide operating voltage range: default working voltage DC4.5V-20V. 7. Micro power consumption: static current <50 automatic control products, especially suitable for dry batteries. 8. Outputs a high level signal: convenient and various circuit to achieve docking. Usage Method 1. Induction module is energized after a minute or so initialization time, during this module will output 0-3 time intervals, to enter the standby mode after a minute. 2. Should try to avoid light interference sources close to the lens surface reflection module, to avoid the introduction of interference signal malfunctions; use of the environment to avoid the flow of wind, wind sensor will also cause interference. 3. Induction module using a dual probe, the probe window is a rectangle, dual (A and B) two end in long direction, when the human body from left to right or right to left walk, infrared spectroscopy to dual time, distance difference, difference is bigger, more sensitive induction, when the human body from the positive to the probe or from top to bottom or from bottom to top through, dual detection not to change, infrared distance without difference, so the inductive insensitive or does not work; so the sensor should be to probe dual direction with the largest number of human activities to the parallel , guarantees the human body after in order to probe the dual induced by. In order to increase the angle sensing range, the module using a circular lens, also makes the probe by induction, but both sides still than the induction range under the direction of two large, sensitivity, still as possible when installed according to the above requirements. Scope Of Application 1. Security products 2. PIR toys 3. PIR light 4. Industrial automation control External Use Thanks Thank you for buying and have a nice time. For more quantity,please contact us. 1) We accept PayPal payment ONLY.