FPV LC Power Filter - LC filter - LPF - JST connectors, US $16.00 – Picture 0

FPV LC Power Filter - LC filter - LPF - JST connectors, US $16.00 – Picture 1

FPV LC Power Filter - LC filter - LPF - JST connectors, US $16.00 – Picture 2

FPV LC Power Filter - LC filter - LPF - JST connectors, US $16.00 – Picture 3

FPV LC Power Filter - LC filter - LPF - JST connectors, US $16.00 – Picture 4

Fpv Lc Power Filter - Lc Filter - Lpf - Jst Connectors

US $16.00

Arendal, AA, Norway
Jan 29th

Open on mobile:
QR code

LPF-01 LC Power Filter Recommended by Team BlackSheep, getFPV and ReadyMadeRC! Technical and installation diagrams, check ivc.no/lpf This is a compact and effective LC filter designed to clean a "dirty" DC power supply for sensitive FPV- and RC-components. The filter has excellent properties to reduce the effect of interference radiated through the air and noise conducted via the power wires. Suitable for setups up to 15V and maximum 1A (1000mA) load. The 3-pin input allows for a single bypass-signal (If rewired from included cables). Problems often occur on sensitive FPV video systems when long power leads (15cm+) are used, limited space for wiring, improperly filtered transmitters, noise from speed controller or switch mode DC-DC voltage converter, or most commonly a shared battery is used to minimize weight. The interference can result in video lines, banding, random drop-outs, and reduced transmission range. A low-pass LC-filter will help attenuation most of the high frequency power supply noise and interference. A common-mode choke coil is used to provide large impedance (resistance) against common-mode current noise picked up by both power leads. It is more effective for noise suppression than conventional ferrite ring and differential-mode inductor setups. This means that noise coming in on both wires will canceled each other out leaving only the regular differential-mode current flowing through the choke. The large series inductor will give good current noise suppression between the input and output. Low resistance of the coils cause only minimum voltage drop over the filter (<200mV) and the low-ESR capacitor used will ensure efficient ripple voltage (noise) reduction (<120mVpk-pk). Only known brand and quality parts are used to offer the great filtering properties. Every filter is tested before being shipped out. One major advantage of this filter compared to others is that both the positive and negative power lines are filtered, so noise can't sneak through the ground line and into your video! Combine it with the Battery Tap and you can easily power your video system directly off of your main flight battery! Specifications Revision: Rev3 March 2013 Type: passive common-mode low-pass power ripple filter Modes: common mode, differential mode - jumper selectable Maximum voltage: 16V DC Maximum current: ~1.5A Cutoff frequency at -3dB: 127 Hz (attenuates higher frequencies/noise) Voltage drop over filter: 180mV at 900mA Maximum voltage ripple: 120mV Capacitor: Japanese Polymer Capacitor Impedance/ESR: 0.012 Ohm at 100kHz/16V Ripple current: 5000mA rms Choke: German Common-mode Choke Series resistance (DC): 0.205 Ohm/path Wire / trace thickness: twisted 22 AWG / 32 mils Operating temperature: -40 °C to +105 °C Dimensions: 37.7 L x 8.8 W x 14.5 H mm Weight: 8.1 grams (inc. JST connectors) RoHS compliant Designed and made in Europe

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	IVC
Country/Region of Manufacture	Norway
Model	LPF-01