US $500.00
Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Manufacturer | FAIRCHILD |
Directions
Similar products from Other Workholding Tools
SCHUNK REDUCTION SLEEVE 201998 SRE S 32 88MM OD 45MM ID (LOC1236A) TS12
SCHUNK REDUCTION SLEEVE TRIBOS 201972 SRE S 6 88MM OD 10MM ID (LOC1236A) TS12
SCHUNK REDUCTION SLEEVE TRIBOS 201992 SRE S 3/4" 88MM OD 3/4" ID (LOC1236A) TS12
SCHUNK REDUCTION SLEEVE TRIBOS SRE S 14 201976 88MM OD 14MM ID (LOC1236A) TS12
SCHUNK REDUCTION SLEEVE SRE S 5/16 8 201973 88MM OD 6.3MM ID (LOC1236A) TS12
JERGENS SERRATED MASTER KEY (QTY 3) 1.5"W 2.44"L 113 015947 (LOC1236A) TS12
MACHINIST TOOLMAKERS HOLD DOWNS PARALLELS LOT
Starrett Jack Screw Set - S190
Lot of 3 3.5" Vise Spacer Non-Factory
Enerpac Hydraulic Vise Jaw Plates VJ-1 Set of 2 NEW
Enerpac Hydraulic Swing Clamp Cylinder RWL-1-V NEW
Enerpac Cylinder Flat Base A-533 NEW
Enerpac Swing Clamp Cylinder RWL 5 NEW
Enerpac Hydraulic Clamp Clamping Cylinder RWH-302 NEW
HYDRAULIC ROTARY CYLINDER TONFOU RC6
HYDRAULIC ROTARY CYLINDER TONFOU RC8
HYDRAULIC ROTARY CYLINDER TONFOU RC10
Sand Paper - Norton Metalite R 226 Delappe Disc - New - Box of 50 Sheets
People who viewed this item also vieved
SUBURBAN Sine Plates Precision 4" x 4" x 2" S0 Steel 3/8-16" Hole SP44S0 |LU1|
Rayco fixturing 1/4-20 adjustable Angle Plate R20-AAP
H/V 5C Horizontal & Vertical Collet Fixture Drill Milling Lathe Grinding
L. S. Starrett Co. Set of 2 Machinist Parallel Clamps 161-D
LOT OF 2 Cam Clamps - Carr Lane
Ace 3.5 Inch Vise Littlestown Vintage Antique Vice
Wilton 10006 Machinist 3" Jaw Round Channel Vise with Swivel Base
Alumiuum Vice Jaws 6" Long 2" Wide 5/8" Thick 3/8-16 Mounting bolts on 4" center
CUSHMAN LATHE CHUCK HARD SOLID JAWS OUTSIDE GRIPPING (10)
CUSHMAN LATHE CHUCK HARD SOLID JAWS OUTSIDE GRIPPING (18)
Hardinge Lathe 6" 2 Jaw Chuck Model 6-2D w/ 2 pcs. Jaws Chuck Key 2 3/16" 10 TPI
vintage lathe end stop and dead center
New ROYAL PRODUCTS #10212 2-MT Live Center W/ NC Point MADE IN USA! New (B26)
HARDINGE TYPE 5C COLLET HEADSTOCK MALE DEAD CENTER
Steel Precision Machinist V-Blocks Lot of (2) 1.875" x 1.875" x 2.875"
V Block, Machinist V Block Made by Toolmaker 2x2x1 1/4
MACHINIST TOOLS LATHE MILL Machinist grinding Adjustable Angle V Block
TROYKE 12" HORIZONTAL ROTARY TABLE - #BH-12
KURT D50 Precision Swivel Base for Anglock D A50-4 Vise USA Genuine KURT
Face plate for 10" super spacer or deluxe rotary index 1.5-8 Threaded Mount Inv2
Young Bros. Young Bros 05091 9 Piece Machine Made Stamp Figure Set, Steel, 3/16"
135mm to 165mm HOOK PIN STYLE SPANNER WRENCH FOR LATHE MILL MACHINIST
PF Anders Collet Set; Case W/collet Holder & 19 Various Sizes Collets; Wrench In
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies